The evaluation of Staphylococcus aureus and Staphylococcus epidermidis in hospital air, their antibiotic resistance and sensitivity of S. aureus to cefoxitin.

Staphylococci as a nosocomial infection agent, increases the possibility of contracting diseases such as wound infection, sepsis and skin infections in humans. It was shown that Staphylococcus aureus considered as a commensal organism causing various both endemic and epidemic hospital-acquired infections. Air samples were collected from Sina Hospital, Hamadan city, which dedicated to various respiratory diseases and analysed by biochemical tests. The resistance and sensitivity of bacterial strains to the cefoxitin antibiotic were also determined. Staphylococcus aureus density (CFU/m3) were measured in the air of various wards as follows: infectious 13.35 ± 7.57, poisoning 29.84 ± 33.43, emergency 8.64 ± 2.72, eye operation room 0, recovery room 6.28 ± 4.90, skin outpatient operation room 4.71 ± 2.36, respiratory isolation 0, ICU 0.79 ± 1.36, and the administrative room 6.28 ± 5.93; while the Staphylococcus epidermidis were as follows: infectious 1.57 ± 2.35, poisoning 2.35 ± 4.08, emergency 2.35 ± 2.35, eye operation room 0, recovery room 0.78 ± 1.36, skin outpatient operation room 2.35 ± 2.35, respiratory isolation 0, ICU 2.35 ± 4.08, and the administrative room 1.57 ± 1.36. The positive and negative control samples showed a concentration of 0. Moreover, among the S. aureus isolates, 33.3% were found to be resistant to cefoxitin, while 40.6% showed to be sensitive. Based on the results, the number of active people and the type and quality of ventilation are very effective in the air quality of various wards of hospital. The poisoning section showed the most contaminated air and the highest resistance and sensitivity to the cefoxitin antibiotic.

Investigation of the effects of different substrates on the promotion of the soil microbial consortium, encompassing bacteria and fungi, in the bioremediation of decabromodiphenyl ether (BDE-209).

Decabromodiphenyl ether (BDE-209) is recognized as an emerging and hazardous pollutant in numerous ecosystems. Despite this, only a few studies have concurrently investigated the biodegradation of BDE-209 by a microbial consortium comprising both bacteria and fungi. Consequently, the interactions between bacterial and fungal populations and their mutual effects on BDE-209 degradation remain unclear. Our main objective was to concurrently assess the changes and activity of bacterial and fungal communities during the biodegradation of BDE-209 in a real soil matrix. In the present study, various organic substrates were employed to promote soil biomass for the biodegradation of BDE-209. Soil respiration and molecular analysis were utilized to monitor biological activity and biomass community structure, respectively. The findings revealed that the use of wheat straw in the soil matrix resulted in the highest soil respiration and microbial activity among the treatments. This approach obviously provided suitable habitats for the soil microflora, which led to a significant increase in the biodegradability of BDE-209 (49%). Biomass survival efforts and the metabolic pathway of lignin degradation through co-metabolism contributed to the biodegradation of BDE-209. Microbial community analysis identified Proteobacteria (Alphaproteobacteria-Betaproteobacteria), Firmicutes, Bacteroides (bacterial phyla), as well as Ascomycota and Basidiomycota (fungal phyla) as the key microorganisms in the biological community involved in the biodegradation of BDE-209. This study demonstrated that applying wheat straw can improve both the biological activity and the biodegradation of BDE-209 in the soil of polluted sites.

Evaluation of Seasonal Variation on the Health Risks Using the Quantitative Microbial Risk Assessment Approach in a Wastewater Treatment Plant in Hamadan, Iran.

BACKGROUND: Wastewater treatment plants (WWTPs) are a source of airborne bacterial contamination that can pose health risks to staff. The aim of this study was to evaluate seasonal variations in the health risks of exposure to Staphylococcus aureus bioaerosols using the quantitative microbial risk assessment (QMRA) approach in a WWTP in Hamadan, Iran. STUDY DESIGN: This was a descriptive cross-sectional study. METHODS: This study determined the emission concentrations of S. aureus bioaerosols in summer and winter. Then, the health risks of three exposure scenarios (the worker, field engineer, and laboratory technician) were evaluated using the QMRA approach. The bioaerosol samples were collected every 12 days in both summer and winter of 2021 with a nutrient agar using a single-stage cascade impactor (Quick Take 30, SKC Inc.) in both outdoor and indoor environments. RESULTS: The results demonstrated that in both seasons, S. aureus bioaerosol concentrations in outdoor and indoor environments were below the standard established by the American Conference of Governmental Industrial Hygienists (500 CFU/m3 ). While in summer, the annual infection risks and the disease burden for the three exposure scenarios in both outdoor and indoor environments were higher than the United States Environmental Protection Agency (≤10-4 pppy) and the World Health Organization (WHO) (≤10-6 DALYs pppy-1) benchmarks, respectively. CONCLUSION: The findings provided high health risks for staff in the three exposure scenarios of an indoor environment, which should not be ignored, as well as emphasizing the use of the QMRA approach to estimate health risks caused by occupational exposure to bioaerosols and taking executive measures to protect staff working in the WWTPs.

Short-term effects of air pollution on hospital admissions of respiratory diseases in Hamadan, Iran, 2015 to 2021.

The short-term effects of air pollution on respiratory diseases have been reported in many countries. Urban areas are most affected because of the many sources of pollution and the large number of people living there. This study aims to investigate the effect of short-term exposure to air pollutants on respiratory hospital admissions in the city of Hamadan. In this ecological study, daily hospital admission data were collected from Shahid Beheshti Hospital in Hamadan. Daily information on air pollutants (CO, SO2, NO2, O3, PM2.5 and PM10) from Hamadan Department of Environment (DoE) organization and of climate factors from Hamadan Meteorological Office were collected. A negative binomial regression model was used to examine the effect of air pollution on daily respiratory hospitalizations. The effect of exposure to pollutants was measured whit different time lags (0-7 days). Furthermore, the effect of meteorological variables was controlled. Subgroup analyses were performed by sex and age group. A total of 12,454 hospitalizations for respiratory diseases were recorded. Results showed a strong and immediate effect of CO on respiratory hospital admissions with highest association at lag 7 (relative risk (RR) = 1.38, 95% CI: 1.33, 1.42). The effects of CO and SO2 on respiratory hospitalizations are greater for men than women. Regarding the short-term effects of PM2.5, SO2 and O3, adults (aged less than 65) were more prone to hospitalization for respiratory diseases. These results show that exposure to air pollution, particularly CO, may increase hospital admissions due to respiratory illness. So reducing the concentration of these pollutants can reduce the number of hospital admissions.

Facile fabrication of amino-functionalized MIL-68(Al) metal-organic framework for effective adsorption of arsenate (As(V)).

An amino-functionalized MIL-68(Al) metal-organic framework (amino-MIL-68(Al) MOF) was synthesized by solvothermal method and then characterized by FESEM, XRD, FTIR, EDX-mapping, and BET-BJH techniques. In order to predict arsenate (As(V)) removal, a robust quadratic model (R2 > 0.99, F-value = 2389.17 and p value < 0.0001) was developed by the central composite design (CCD) method and then the genetic algorithm (GA) was utilized to optimize the system response and four independent variables. The results showed that As(V) adsorption on MOF was affected by solution pH, adsorbent dose, As(V) concentration and reaction time, respectively. Predicted and experimental As(V) removal efficiencies under optimal conditions were 99.45 and 99.87%, respectively. The fitting of experimental data showed that As(V) adsorption on MOF is well described by the nonlinear form of the Langmuir isotherm and pseudo-second-order kinetic. At optimum pH 3, the maximum As(V) adsorption capacity was 74.29 mg/g. Thermodynamic studies in the temperature range of 25 to 50 °C showed that As(V) adsorption is a spontaneous endothermic process. The reusability of MOF in ten adsorption/regeneration cycles was studied and the results showed high reusability of this adsorbent. The highest interventional effect in inhibiting As(V) adsorption was related to phosphate anion. The results of this study showed that amino-MIL-68(Al) can be used as an effective MOF with a high surface area (> 1000 m2/g) and high reusability for As(V)-contaminated water.

Evaluation of SARS-CoV-2 in Indoor Air of Sina and Shahid Beheshti Hospitals and Patients' Houses.

Side by side air sampling was conducted using a PTFE filter membrane as dry sampler and an impinger containing a suitable culture medium as a wet sampler. Most of the samples were collected from two hospitals and few air samples were collected from private houses of non-hospitalized confirmed COVID-19 patients. The collected air samples were analyzed using RT-PCR. The results indicated that all air samples collected from the hospitals were PCR negative for SARS-CoV-2. While two of four air samples collected from the house of non-hospitalized patients were PCR positive. In this study, most of the hospitalized patients had oxygen mask and face mask, and hence this may be a reason for our negative results regarding the presence of SARS-CoV-2 in indoor air of the hospitals, while non-hospitalized patients did not wear oxygen and protective face masks in their houses. Moreover, a very high concentration of particles in the size range of droplet nuclei (< 5 µm) was identified compared to particles in the size range of respiratory droplets (> 5-10 µm) in the areas where patients were hospitalized. It can be concluded that using face mask by patients can prevent the release of viruses into the indoor air, even in hospitals with a high density of patients.

Effect of household processing on pesticide residues in post-harvested tomatoes: determination of the risk exposure and modeling of experimental results via RSM.

This study aimed to investigate the acute and chronic hazard quotients of chlorpyrifos and diazinon for tomatoes in preharvest and postharvest conditions, and to evaluate the relationship between the main variables, including temperature and contact time and pesticide dissipation at different conditions using response surface methodology for the first time. The qualification analyses were conducted by a gas chromatography-tandem mass spectrometry. The Monte Carlo simulation technique was utilized to evaluate the variability and uncertainty and achieve more accurate results in the health risk assessment process. A quadratic model and the second-order polynomial analysis were employed to investigate the mutual effect of time and temperature on removing diazinon and chlorpyrifos. Based on findings, the chronic hazard quotient values of chlorpyrifos and diazinon residues ranged from 0.43 - 1.33 to 0.13 - 2.27 for boiling, 0.65 - 1.49 to 3.05 - 7.15 for room condition, and 0.63 - 1.92 to 3.28 - 7.47 for refrigerator condition, respectively. According to the Monte Carlo simulation, the hazard quotient and estimated daily intake values were more affected by the consumption rate, pesticide concentration, and body weight. The results of response surface methodology showed that the effect of temperature variations on the dissipation of both pesticides was more than that of contact time variations.

Pesticide residues levels as hematological biomarkers-a case study, blood serum of greenhouse workers in the city of Hamadan, Iran.

The cultivation of greenhouse crops is the most severe form of crop production in Iran, and vast quantities of unreasonable pesticides are being utilized to control the pests. The residual level of blood pesticides and their correlation with multibiomarkers were determined to evaluate the adverse health consequences on greenhouse workers in the Hamadan, west of Iran. Participants were 180 adult males, including 90 greenhouse workers exposed to pesticides and 90 control individuals. Blood samples were taken from all subjects for pesticide residues analysis, and hematological and biochemical parameters. The blood pesticide residues were analyzed using gas chromatography (GC) with a flame ionization detector. Hematological and biochemical parameters were determined using hematology cell counter and auto analyze, respectively. Statistical analyses were done with STATA version 14.2 software. The multivariate regression was used for relationship between various pesticide concentrations in blood and changes in biomarkers in pesticide exposed group. The analyses revealed that 64 out of the 90 workers had residues of dichlorvos, diazinon, and chlorpyrifos in their blood serum, and 56.25% out of these workers were exposed for >15-year period. The residues of all three pesticides were higher than the no observable adverse effect level (NOAEL) in all the exposure duration categories. Comparisons of hematological parameters showed that mean monocyte (0.76±0.41, P < 0.001), lymphocyte (3.52±1.20, P < 0.001) and platelet counts (278.18±66.05, P=0.001), mean platelet volume (10.18±0.59, P=0.002), and plateletcrit (PCT) (0.275±0.05, P<0.001) were significantly higher in workers than the controls, whereas hemoglobin (HB) (14.61±1.28, P=0.028), mean corpuscular hemoglobin (MCH), and mean corpuscular hemoglobin concentrations (MCHC) (32.44±0.90, P<0.001) were lower in workers than controls. These results indicate that the exposed individuals have experienced significant hemotoxic effects during the pesticide exposure. The study also predicts the risk to exposed individuals in developing countries like Iran and demands realization of safety measures to prevent such dangerous effects of pesticide exposures.

Step-scheme BiVO4/WO3 heterojunction photocatalyst under visible LED light irradiation removing 4-chlorophenol in aqueous solutions.

In the present study, photodegradation of 4-chlorophenol (4-CP) using a step-scheme BiVO4/WO3 heterostructure under visible LED light irradiation (Vis LED) from aqueous solutions was investigated. The photocatalyst was synthesized through the hydrothermal process and characterized physically and chemically via X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), energy-dispersive X-ray (EDX), and Brunnauer-Emmett-Teller (BET) techniques. The effects of the operational parameters i.e., solution pH, contact time, nanocomposite dosage, and initial 4-CP concentration were evaluated. Results indicated that BiVO4/WO3/Vis LED process has higher efficiency in 4-CP degradation than BiVO4/Vis LED, WO3/Vis LED, and BiVO4/WO3 systems. At BiVO4/WO3 concentration of 0.125 g/L, initial pH of 7, and initial 4-CP concentration of 25 mg/L, complete degradation of 4-CP (>97%) was achieved in reaction time of 60 min. The phenol, chlorobenzene, catechol, 4-chlorocatechol, 5-chloro-1,2,4-benzenetriol, hydroquinone, hydroxyhydroquinone, p-benzoquinone, o-benzoquinone, formic acid, acetic acid, and oxalic acid were identified as the major intermediates of 4-CP degradation. In optimal condition, 67.5% and 88.5% of TOC and COD removal rates were obtained in 120 min contact time, respectively. The degradation of 4-CP was pseudo-first-order kinetics. Through the use of tert-Butyl alcohol (TBA) and ethylenediamine tetraacetic acid (EDTA) as radical scavengers, hydroxyl radicals and holes were identified as the main active species in photocatalytic degradation. Also, a tentative pathway for 4-CP degradation using the Vis LED/BiVO4/WO3 process was proposed.

Characteristics and health effects of potentially pathogenic bacterial aerosols from a municipal solid waste landfill site in Hamadan, Iran.

The aim of this study was to evaluate the potential pathogenic bacterial aerosols produced from the municipal solid waste landfill site and its health risk assessment in the Hamadan city at west of Iran. In this study, air samples were collected every month during spring and summer at six locations including the active zone, leachate collection pond, infectious waste landfill, upwind, closure landfill, and downwind using the Andersen impactor. Spatial and seasonal variations of the potential pathogenic bacterial aerosols were detected. Also, Health risk associated were estimated based on the average daily dose rates (ADD) of exposure by inhalation. The mean concentration of potentially pathogenic bacterial aerosols were 468.7 ± 140 CFU m- 3 1108.5 ± 136.9 CFU m- 3 detected in the active zone in spring and summer, respectively. Also, there was a significant relationship between meteorological parameters and bacterial concentration (p < 0.05). The predominant potential pathogenic bacterial identified in the spring were Proteus mirabilis, Streptococcus sp., and Pseudomonas sp., while in summer were Pseudomonas sp., Staphylococcus aureus, and Escherichia coli. The hazard quotient (HQ) in both seasons were less of 1. Bacteria were spread throughout the landfill space, but their maximum density was observed around the active zone and leachate collection pond. This study highlights the importance of exposure to potential pathogenic bacterial aerosols in the summer and its adverse effects, especially in the MSW landfill site active zone. Finally, controlled exposure can reduce the health hazard caused by the potential pathogenic bacterial aerosols.

Short-term effect of multi-pollutant air quality indexes and PM2.5 on cardiovascular hospitalization in Hamadan, Iran: a time-series analysis.

Air pollutants are the most important environmental factors that contributed to cardiovascular disease (CVD). The present study aimed to investigate the number of hospitalization due to heart failure (HF) and myocardial infarction (MI) following the air pollutant exposure using a time-series regression analysis with a distributed lag model in Hamadan, Iran (2015-2019). A total of 2091 cases of CVD were registered. Based on the findings, the highest health effects on HF hospitalization were observed with air quality health index (AQHI) at lag 9 (RR = 1.043, 95% CI 0.991-1.098), and air quality index (AQI) at lags 2, 7, and 9 (RR = 1.001, 95% CI 0.998-1.002), for an increase in 1 unit of the indexes, and with PM2.5 at lag 0 (RR = 1.001, 95% CI 0.996-1.004) for 10 µg/m3 increase in PM2.5 levels. The highest health effects on MI hospitalization were calculated with AQHI at lag 10 (RR = 1.059, 95% CI 1.001-1.121) and AQI at lags 1 and 2 (RR = 1.001, 95% CI 0.998-1.002), for an increase in 1 unit of the indexes, and with PM2.5 at lag 8 (RR = 1.002, 95% CI 0.997-1.005) for 10 µg/m3 increase in PM2.5 levels. According to a seasonal classification, results showed that hospitalization in the warm season was higher than that of the cold season. Based on our knowledge, the current study is the first study that investigated the effect of air quality indexes on hospitalization due to HF and MI in Iran. Findings can provide basic information to plan preventive measures for reducing exposure chance and hospitalization rate in high-risk people.

Electrocatalytic degradation of diuron herbicide using three-dimensional carbon felt/ß-PbO2 anode as a highly porous electrode: Influencing factors and degradation mechanisms.

Traditional planar PbO2 anodes have been used extensively for the electrocatalytic degradation process. However, by using porous PbO2 anodes that have a three-dimensional architecture, the efficiency of the process can be significantly upgraded. In the current study, carbon felt (CF) with a highly porous structure and a conventional planar graphite sheet (G) were used as electrode substrate for PbO2 anodes. Both CF/ß-PbO2 and G/ß-PbO2 anodes were prepared by the anodic deposition method. The main properties of the electrodes were characterized by XRD, EDX-mapping, FESEM, and BET-BJH techniques. The electrocatalytic degradation of diuron using three-dimensional porous CF/ß-PbO2 anode was modeled and optimized by a rotatable central composite design. After optimizing the process, the ability of porous CF/ß-PbO2 and planar G/ß-PbO2 anodes to degrade and mineralize diuron was compared. The electrocatalytic degradation of the diuron was well described by a quadratic model (R2 > 0.99). Under optimal conditions, the kinetics of diuron removal using CF/ß-PbO2 anode was 3 times faster than the G/ß-PbO2 anode. The energy consumed for the complete mineralization of diuron using CF/ß-PbO2 anode was 2077 kWh kg-1 TOC. However, the G/ß-PbO2 anode removed only 65% of the TOC by consuming 54% more energy. The CF/ß-PbO2 had more stability (115 vs. 91 h), larger surface area (1.6287 vs. 0.8565 m2 g-1), and higher oxygen evolution potential (1.89 vs. 1.84 V) compared to the G/ß-PbO2. In the proposed pathways for diuron degradation, the aromatic ring and groups of carbonyl, dimethyl urea, and amide were the main targets for HO• radical attacks.

Phase distribution and risk assessment of PAHs in ambient air of Hamadan, Iran.

In the present study, both gaseous and particulate (PM with dae <2.5 µm) phases of polycyclic aromatic hydrocarbons (PAHs) were measured in the ambient air of Hamadan city, Iran. For this reason, two low-volume samplers equipped with glass fiber filters were used for sampling of particulate phase (N = 30) and XAD-2 sorbent tubes were applied for sampling gaseous phase of PAHs (N = 30). The sampling was conducted during warm and cold seasons in 2019. The average of cold/warm season ratios for Σ16PAH and PM concentrations were 1.14 and 0.62, respectively. Summed PAHs concentration were determined to be in the range 0.008-59.46 (mean: 11.61) ng/m3 and 0.05-40.83 (mean: 10.22) ng/m3 for the cold and warm seasons, respectively. A negative Pearson correlation coefficient was obtained for wind speed and relative humidity. The average Benzo (a) Pyrene equivalent carcinogenic (BaPeq) levels in the cold season were lower than the maximum permissible risk level of 1 ng/m3 for BaP. The BaP toxicity equivalency (ΣBaPTEQ) and BaP mutagenicity equivalency (ΣBaPMEQ) appeared to be significantly higher in the cold season (averaging 0.35 and 1.65 ng/m3, respectively) than those in warm season. Health risk assessment was performed for children and adults based on BaPeq, inhalation cancer risk. The diagnostic ratios of individual PAHs concentration showed that the significant sources of PAH emissions may be related to light duty vehicles (LDVs) in Hamadan. Although, some other sources such as pyrogenic source and petrol combustion were also suggested.

An assessment of the occurrence and nutritional factors associated with aflatoxin M1, ochratoxin A, and zearalenone in the breast milk of nursing mothers in Hamadan, Iran.

This research investigated the occurrence of aflatoxin M1 (AFM1), ochratoxin A (OTA), and zearalenone (ZEN) in human milk samples in the Hamadan city, Iran. The study was carried out using the milk of nursing mothers from ten governmental health care centers. Mycotoxin content of ninety milk samples measured using enzyme-linked immunosorbent assay (ELISA). All samples that tested positive for AFM1 with the ELISA test were subsequently analyzed by high-performance liquid chromatography (HPLC). The mean ± SD concentrations of AFM1, determined by ELISA and HPLC were 5.98 ± 1.47 and 4.36 ± 1.23 ng/L, respectively. OTA and ZEN levels were below the detection limit (<5 ng/L) in all samples. None of the contaminated samples exceeded the regulation limit set by the European Commission (25 ng/L) for AFM1 in infant formula. We found a significant correlation between the AFM1 concentration in breast milk and infant age and milk consumption by the nursing mother (p < 0.05). These findings revealed that infants are susceptible to AFM1 exposure from their mother's milk. The authors recommend that additional research be conducted on the analysis of foodstuff and biological fluids for various mycotoxins.

Sampling and detection of corona viruses in air: A mini review.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is a strain of coronaviruses that causes coronavirus disease 2019 (COVID-19). In these days, the spread of the SARS-CoV-2 virus through the air has become a controversial topic among scientists. Various organizations provide standard methods for monitoring biological agents in the air. Nevertheless, there has been no standard recommended method for sampling and determination of viruses in air. This manuscript aimed at reviewing published papers for sampling and detection of corona viruses, especially SARS-Cov-2 as a global health concern. It was found that SARS-Cov 2 was present in some air samples that were collected from patient's rooms in hospitals. This result warrants its airborne transmission potential. However, due to the fact that in the most reviewed studies, sampling was performed in the patient's room, it seems difficult to discriminate whether it is airborne or is transmitted through respiratory droplets. Moreover, some other disrupting factors such as patient distance from the sampler, using protective or oxygen masks by patients, patient activities, coughing and sneezing during sampling time, air movement, air conditioning, sampler type, sampling conditions, storage and transferring conditions, can affect the results. About the sampling methods, most of the used samplers such as PTFE filters, gelatin filers and cyclones showed suitable performance for trapping SARS-Co and MERS-Cov viruses followed by PCR analysis.

A comparative study for the removal of imidacloprid insecticide from water by chemical-less UVC, UVC/TiO2 and UVC/ZnO processes.

BACKGROUND: Chloronicotinic insecticide are a class of pesticides that are commonly used as insecticides. Among the frequently used chloronicotinic pesticide, imidacloprid (IM) was developed in 1986. The residual of this insecticide or any pesticides may have serious public health threats. METHODS: Both degradation and mineralization of the imidacloprid (IM) in aqueous solution was studied under various experimental conditions using different advanced oxidation processes namely, ultraviolet C (UVC), UVC + TiO2, and UVC + ZnO. All the experiments were performed using a lab-scale batch photoreactor with a working volume of 100 mL equipped with low-pressure mercury vapor lamp (9 W, 18 cm long, Philips Co.), emitting UV radiation with maximum intensity at 254 nm. The possible intermediates and a reaction pathway for photocatalytic degradation of the IM were also evaluated. RESULTS: It was observed that under optimal condition for UVC/TiO2 process (C0 = 100 mg/L, pH = 7.5, t = 20 min, TiO2 dose = 100 mg/L), IM was effectively degraded (88.15%) and followed the first order kinetics model. The degradation efficiency increased with increasing of illumination time and is more favorable in alkaline pH compared to acidic pH. Degradation of the IM in photocatalytic process was compared with photolysis showing a significant synergy effect in the case of the photocatalytic degradation process, leading at 20 min illumination time to a 36.7% increase of the IM removal efficiency in comparison to the single UVC. The GC/MS chromatograms before and after treatment confirmed the effectiveness of the UVC/TiO2 process in simplifying the nature of IM and its conversion to more simple and degradable compounds. CONCLUSION: The heterogeneous UVC/TiO2 process was found to be an efficient chemical-less method that is appropriate for degradation of IM from aqueous phase.

The Assessment of Trihalomethanes Concentrations in Drinking Water of Hamadan and Tuyserkan Cities, Western Iran and Its Health Risk on the Exposed Population.

BACKGROUND: The aim of the present study was to calculate and to assess the potential lifetime cancer risks for trihalomethanes from consuming chlorinated drinking water in Hamadan and Tuyserkan cities, western Iran in 2016-2017. STUDY DESIGN: A cross-sectional study. METHODS: Seventy-two water samples were collected from the distribution systems and from the outlet of water treatment plants (WTPs) and the experiments were carried out to determine the desired parameters. All the sampling and measurement methods were according to Standard Methods. The obtained data were analyzed using SPSS software. RESULTS: The mean concentration of total THMs in the summer and winter was 42.75 and 17.75 µg/L, respectively, below the WHO and Iranian standard. The positive correlation was observed between temperature and THMs levels. Moreover, THMs concentration in Shahid Beheshti's WTP was several times lower than in Ekbatan's WTP. Chloroform, the dominant species of THMs, was identified at different sampling points. The highest cancer risk in Hamadan was 1.4×10-5 and 4.8×10-5 for male and female, respectively; and the cancer risk was obtained to be 5.6×10-7-2.26×10-6 in Tuyserkan. CONCLUSION: The drinking water obtained from the studied area is safe in terms of THMs concentration. Nevertheless, the highest cancer risk was higher than the EPA's acceptable level of 10-6.

Exposure to heavy metals released to the environment through breastfeeding: A probabilistic risk estimation.

Toxic heavy metals released into the environment through various anthropogenic activities, raising concerns over their potential adverse effects on human health and the environment. Biological monitoring studies are of great value in toxicological research for estimation of such health effects. The aim of this study was to evaluate the concentrations of lead (Pb), arsenic (As), and chromium (Cr) in the breast milk of urban mothers in Hamadan city, Iran and the accompanying health risk to infants. A total of 100 lactating mothers were recruited from public health care centers in Hamadan city and breast milk samples were collected at 2, 6, 8, and 12 months postpartum. Inductively coupled plasma mass spectroscopy (ICP-MS) has been used to measure target heavy metal concentrations. The median breast milk concentrations of Pb, As, and Cr were 41.90, 0.50, and 3.95 µg/L, respectively. The highest levels of Pb were observed after two months of delivery (with the mean of 96.69 µg/L and median of 45.70 µg/L). Up to 94% of the breast milk samples exceeded the WHO limit suggested for lead contamination of breast milk (<5 µg/L). The breast milk As and Cr contents were above the limit of detection (LOD) in 19% and 76% of samples, respectively. Unacceptable non-cancer health risk levels or hazard quotient (HQ) were found for Pb and As in 61% and 10% of the samples, respectively. Nevertheless, HQ from Cr was <1.0 for 100% of breastfeeding infants. Finally, our results indicated that there may be a potential risk of toxic metals, especially lead, for infants in Hamadan via the consumption of mothers' breast milk.

Mercury, Lead, Cadmium, and Barium Levels in Human Breast Milk and Factors Affecting Their Concentrations in Hamadan, Iran.

Breast milk is considered the best source of nutrition for all infants. However, exposure of newborns to toxic metals is of special interest due to their potential harmful effects. Thus, the primary aims of this study were to determine the concentration of toxic heavy metals including lead, mercury, cadmium, and barium in breast milk samples from Hamadan, Iran, in relation to some sociodemographic variables. A total of 100 breast milk samples were collected and their heavy metal contents were measured by inductively coupled plasma mass spectroscopy (ICP-MS). The median breast milk concentrations of Pb, Hg, and Ba were 41.9, 2.8, and 1.95 µg/L, respectively. Cd levels were < 1 µg/L in all samples. The Pb level in 94% of the samples was higher than the recommended Pb limit of < 5 µg/L in breast milk suggested by World Health Organization (WHO). Hg levels in 54% of the breast milk samples were higher than the normal mean concentration (1.7 µg/L) suggested by WHO. We found no correlation between Hg levels in breast milk and sociodemographic factors. Ba levels in all the breast milk samples were lower than the WHO's proposed health-based drinking water guideline (0.7 mg/L). Considering the results of the present study and the vulnerability of infants, along with the well-known toxicity of these metals, further studies are warranted to identify the main sources of exposure that contribute their concentration in breast milk, establish harmless intake values of toxic metals in breast milk, and develop preventive measures.

Analysis of aluminum, minerals and trace elements in the milk samples from lactating mothers in Hamadan, Iran.

The present cross-sectional study is aimed at analyzing the breast milk of lactating mothers in Hamadan, Iran for aluminum and several minerals and trace elements. Ten governmental health care centers were utilized to facilitate collection of breast milk samples. The breast milk samples were collected at 1, 2, 6, 7, and 12 months postpartum from one hundred healthy lactating women, who delivered full-term newborns. Detection of sodium (Na), zinc (Zn), calcium (Ca), iron (Fe), copper (Cu), magnesium (Mg) and aluminum (Al) levels was conducted with the use of Inductively Coupled Plasma Mass Spectrometry (ICP-MS). This method has shown high accuracy, precision, sensitivity, and linearity for the wide range of concentrations. The accumulated data were not normally distributed; thus, the non-parametric Mann-Whitney U test was used in the statistical analysis of the results. Mean concentrations of Fe, Zn, Cu, Ca, Mg, and Na were 0.75, 1.38, 0.35, 255, 34.58, and 155.72 µg/mL, respectively. The mean level of Al, a well-known neurotoxic metal, was determined to be an alarming 0.191 µg/mL. Moreover, 95% of participants contained very harmful concentrations of Al in their milk. This study also revealed Zn deficiency in about 50% of milk samples. Further investigation is needed to elucidate sources of exposure and factors that may influence maternal and fetal exposure to aluminum.